Sanding drywall: When sanding drywall seams, it's good to follow the seam instead of going against it. It's better to go in circles, this way everything is blended and faded instead of getting that "path" from over sanding. Use a scrap piece of lumber or something hard and flat to put under your sand paper, this will keep things uniform. Using your hand can result in high and low spots which ultimately leads to more work. Also if you need the seams to dry quickly, try mixing your own "mud" instead of using the premix. The powedered mix comes in drying times of 20 minute, 45 minute, and 90 minute. The work times aren't very long with these so keep moving!
Pane in the glass: So a window has just become the victim of a solid object traveling at a fairly good speed, now what do you do? (If you have traditional windows in your house or garage, follow these steps. If you have thermal pane or other insulated glass, call a glass company to order a replacement unit.) Time to remove the glass from the frame, this is better done from the outside if possible because the glass goes in from this direction. Wearing gloves and eye protection use a pair of pliers to grab the shards, if the glass breaks under the galzing a chisel will work to remove both. After the area is free of glass and glazing measure the opening and give yourself 1/8" in both directions. Call your local glass company and have the glass cut, if the frame isn't completely sqaure a wood chisel can be used to "adjust" the opening to accomodate the new pane. Also, pick up a box of points from the glass company, thses are used to hold the glass in the frame. Apply new glazing and you're done.
Caulking: Caulking can be a messy job that results in what looks like a 3 year old played arts and crafts with your house. Not to worry, here are a few tips to help you out. Around glass or a finished surface, use painters tape on either side of the joint being caulked. This will save you time on clean up and it's ok if the process gets a little messy, if caulk gets on the tape you can peel it right up. For the "professional" look, wet your finger and run it down the bead to smooth it out and remove the excess, this will also work if you want to use a putty knife. Just wet the knife and run it down the bead. Using a putty knife to tool the caulk or window glazing may take some practice. Part of the blade will need to follow a flat surace to keep things looking good, every movement made or bump the knife hits will show up in the caulk. Also be careful not to remove to much caulk or it will be ineffective. Follow the manufacturers recommendations for proper adhesion and sealing. Happy caulking.
When sweating pipe in confined areas (near walls, inside cabinets, behind the tub) use a piece of galvanized 90 degree flashing. This will direct the heat and the flame away from combustables and, if sweating near a wall finished or not, drywall/paint. Don't use prepainted flashing as the paint may smolder or catch fire.
Senario: You have this awesome piece of trim that you just pulled off the wall and you want to reuse it. The problem is the nails are stuck in it. How do you get them out? "Duh, simple.", right.....maybe not. Instead of knocking the nails out from back to front, pull them the rest of the way through the board. If you go the "traditional" route there is a chance that this piece of trim will be damaged and that means filler and trying to match stain or paint. A good pair of pliers should give you enough grip to pull the nails straight on through.
I have read a few articles on msn.com lately about contractors and home projects. These articles are good thought provokers and bring to light some good points, but maybe some that don't apply to your particular area, county, or city. Obviously if you are doing a home remodel project on a house you plan on selling, you want to make sure the project will add value to your home as well as functionality. If you don't plan on selling the home, then adding value may not be as important as funtionality or "want to". It's your decision and your home, take your time and make lists.
In these difficult times there may be some shady contractors or even fly-by-night guys out there. If you want quality work there is a price to be paid. Here's a good saying: "Cheap work isn't good and good work isn't cheap." Not always the case, but something to keep in mind. I know statistically the price of work has come down, but the price of material has not. So you might find the contractor cheaper, but expect to pay the same if not more for material. Many contractors out there are willing to discount their work just to get the job and there's nothing wrong with helping those in your community out. The things I would watch out for are guys you charge not only for material used on the job, but all the material they bought and maybe even contractors who charge by the hour. In remodeling you don't know what you are going to find behind drywall or plaster or under the floor or in the pipes until you get into it. There's nothing worse than under estimating and over paying. For me it's just easier to charge by the job and then however long it takes is on me. It also may be a good idea to check with your local Chamber of Commerce to see if the contractor is a member. The guys who invest in their community are the ones you can normally count on. Also, if something should happen to be wrong or go wrong after completion, a good contractor will come back and fix it at no cost.
There may be some unique situations also. If you know a contractor personally or have a good relationship with one, there may be times where some "experimentation" comes up. New systems or new materials may be introduced or maybe it's just gain some experience, the contractor may approach the home owner with this idea. I guess the home owner may approach the contractor with this idea, who knows it's a crazy world. If this situation does come up you ,the homeowner, could possibly get the work done for the price of materials. Just saying, if you don't mind being the guinea pig it might be a worth while venture.
All in all, remodeling and renovation don't have to be scary or bad projects. Make some lists, decide what you want and start asking questions. Contractors may not have all the answers and may have questions themselves. It's going to take time, life isn't a one hour tv show, it going to take some money, and there will be dust. Remember, the lowest bid isn't always the best and the job will only be as good as the material you are working with. Don't expect a million dollar bathroom for two thousand dollars. Happy remodeling!
Mothers Day is this Sunday, if you have a project you want to complete or maybe you just want to surprise her by getting that "Honey Do" list out f the way. Call us this week and receive 20% off any services we provide. Work must start this week. Also, please enter your contact info at the bottom of the home page so we can keep track of who takes advantage of this deal. Let's show mom how much we care and that she is important enough to us to get things done!
Well, it's finally spring and the weather is starting to come around. We just finished up a small kitchen remodel, replacing everything from the plumbing to the cabinets and counter tops. We had to kill some mold on the subfloor before we built it up and removed some lead paint on the walls. I'll get some before and after pics up. Also Property Serv just landed a contract with a local Bank to go and rewire and re-plumb a house. It's fixing issues the previous owner created after the house was foreclosed on. It will be a couple of weeks worth of work, but I'm happy for it.
Have you ever went to your local home improvement store for a counter top and just didn't like what they had in stock? Then the sales person wants you to special order something, but come to find out it's four times as much as the off the shelf stuff. Well, if you're not installing granite or some other natural stone or exotic product, why not fabricate your own. As most of you know, I'm renovating a house from 1890 (though there isn't anything from that time period that I have found) and I have put in new kitchen cabinets and flooring. All of the "stock" counter tops that I found had back splashes on them and to special order was about four times as much. So, I decided to fab my own. Nothing extravagant right now, just particleboard with a laminate covering. I'll add the back splash later (I'm going to use some of the split stone granite all the way across), the thing is it will be custom and the way I want it to look without having to spend hundreds and have to wait weeks on the factory. It's also good experience and a useful skill. Joining the pieces may prove a challenge (over 11 feet of base cabinets on one side), but I'm sure I have it figured out. I get pics up soon.
Property Serv LLC now has financing options available for your projects. Here is how it works; when a home owner hires Property Serv, but does not have enough cash to cover materials, let's say. The home owner can fill out a loan application from PCCU Credit Union, fax it in or drop it by, and can have an answer quickly. The loans can be broken down into manageable monthly payments with great rates and the work can begin. This is a great option to get alot now without breaking the bank. Protecting your investment and your nest egg is important to Property Serv LLC and PCCU Credit Union.
Craig Jones, owner of Property Serv LLC. My goal is to better educate the homeowner and to make Richmond a better place to live.